Author Topic: Hoofies How to (Read 20393 times)

Jason · « **on:** October 02, 2007, 07:33:30 PM »

How to assemble and fit Hoofies

To start this is what you get to make a Hoofie (you get 2 in a set

)

If you have the later bolt on rubber hoofs you will have 2 large washers and 2 small (for each hoofie)

Jason · « **Reply #1 on:** October 02, 2007, 07:34:48 PM »

Take a bolt, washer and the short nylon strap and assemble thus

Jason · « **Reply #2 on:** October 02, 2007, 07:35:39 PM »

Now thread the bolt through the rubber base like this

Jason · « **Reply #3 on:** October 02, 2007, 07:36:35 PM »

Next bend the front of the rubber base back and thread the bolt through the front hole

Jason · « **Reply #4 on:** October 02, 2007, 07:37:24 PM »

Fit a washer and nut to the bolt
On the later bolt on rubber type these washers on the inside are the small ones

Jason · « **Reply #5 on:** October 02, 2007, 07:38:10 PM »

Slide the Hoofies label onto the nylon strap (optional

) and thread the second bolt like the first
Now the hard bit pull the front of the base up and thread the blot through first the back hole then the front (same as other side)

Jason · « **Reply #6 on:** October 02, 2007, 07:38:52 PM »

Fit another washer and nut and it should look like this

On the later bolt on rubber type these washers on the inside are the small ones

Jason · « **Reply #7 on:** October 02, 2007, 07:39:42 PM »

Tighten both nuts while keeping everything straight make sure they are very tight so this much thread sticks into the Hoofie

Jason · « **Reply #8 on:** October 02, 2007, 07:40:31 PM »

The front should look like this now

Jason · « **Reply #9 on:** October 02, 2007, 07:41:15 PM »

Take the long strap and thread it throught the rubber base from the back like this note which way up the strap is

Jason · « **Reply #10 on:** October 02, 2007, 07:42:01 PM »

It should look like this

Jason · « **Reply #11 on:** October 02, 2007, 07:42:48 PM »

Thread the strap through the second hole and pull it tight down against the base

Jason · « **Reply #12 on:** October 02, 2007, 07:43:38 PM »

It should look like this at the back you can now repeat all this on the second hoofie but put the strap through from left to right (other way)

Jason · « **Reply #13 on:** October 02, 2007, 07:44:41 PM »

Now to fit them

Look at the front of the hoofs on your Pro-jumps they should look like this the 2 yellow marks are to show where the bolts on the hoofies hook over the rubber hoofs

Jason · « **Reply #14 on:** October 02, 2007, 07:45:25 PM »

Take the hoofie and push it on to the front of the hoof as shown (push it very hard all the way on)

Jason · « **Reply #15 on:** October 02, 2007, 07:46:04 PM »

Here is a pic of the bolt position once it is on

Jason · « **Reply #16 on:** October 02, 2007, 07:46:49 PM »

This is how it should look from the top

Jason · « **Reply #17 on:** October 02, 2007, 07:47:26 PM »

Now take the strap guard

Jason · « **Reply #18 on:** October 02, 2007, 07:48:04 PM »

And velcro it on just above the hoof like so (this is important as the top edges of the frame can be sharp you should check this occasionaly for wear)

Jason · « **Reply #19 on:** October 02, 2007, 07:48:48 PM »

Thread the long strap through itself as shown

Jason · « **Reply #20 on:** October 02, 2007, 07:49:22 PM »

Now while keeping everything straight and even pull the strap tight

Jason · « **Reply #21 on:** October 02, 2007, 07:49:58 PM »

Pull it over and velcro shut as shown ( it has to be quite tight )

Jason · « **Reply #22 on:** October 02, 2007, 07:50:30 PM »

Pass the strap round the back

Jason · « **Reply #23 on:** October 02, 2007, 07:51:22 PM »

Pull it tight

Jason · « **Reply #24 on:** October 02, 2007, 07:52:04 PM »

Attach to the velcro at the front and your done now do the other one

News:

Author Topic: Hoofies How to (Read 20393 times)